ভাষাসমূহ

Write down the differences between: Relays and magnetic contactors; wires and cables; 1-phase (1Ø) and 3-phase (3Ø) systems; SI (petrol/gasoline) and CI (diesel) engines; circuit breakers, auto-reclosers, fuses, and isolators; Author: Engr. Dibakar Dey

Text size A A A
Color C C C C

Write down the differences between: Relays and magnetic contactors; wires and cables; 1-phase (1Ø) and 3-phase (3Ø) systems; SI (petrol/gasoline) and CI (diesel) engines; circuit breakers, auto-reclosers, fuses, and isolators; and air circuit breakers versus oil circuit breakers. Author: Engr. Dibakar Dey, IIT-Kharagpur, India.

Question: State the differences between a relay and a magnetic contactor.

Answer: The differences between a relay and a magnetic contactor are as follows:

Relay

Magnetic Contactor

1. Relays have a low ampere rating (max. 20A).
1. Magnetic contactors have higher ampere ratings (up to 12,500 A).

2. Relays are typically used in control circuits, automation, and electronic circuits.

2. Magnetic contactors are typically used in motors, capacitor banks and power circuits.

3. Relays are typically single-phase.

3. Magnetic contactors are generally available in single-phase and three-phase versions.

4. There is no provision for arc extinction within the relay.

4. Magnetic contactors include a mechanism for extinguishing arcs.

5. Small size and low cost. 
6. Big size and high cost. 

Question: State the difference: 1Ø & 3Ø?

Answer: Difference between 1Ø & 3Ø

1Ø

3Ø

1. The connection is made using two wires: one is the phase/line, and the other is the neutral.

1. The connection is made using four wires: three phases and one neutral.

2. Only single-phase loads can be operated.

2. Both single-phase and three-phase loads can be operated.

3. Used for low-load applications. for example, in homes, shops, etc.

3. Used for high-load applications. for example, in mills, factories, etc.

4. High losses and low efficiency.

4. Low losses and high efficiency.

5. Voltage(VPh) = 220–230 volts.

5. Voltage(VL) = 400–415 volts. (VL =  1.732 x VPh)

Question: State the difference: S.I and C.I Engine

Answer: Difference Between S.I and C.I Engine

S.I. (Petrol/Gasoline)

C.I. (Diesel)

1. Petrol or gasoline engines operate on the Auto-cycle.

1. C.I. engines operate on the diesel cycle.

2. In a petrol or gasoline engine, air and fuel enter the cylinder during the suction stroke.

2. In a diesel engine, only air enters the cylinder during the suction stroke.

3. For the combustion process in a petrol or gasoline engine, components such as a battery, ignition coil, C.B. points, distributor, and spark plug are required.

3. To facilitate the combustion process in a diesel engine, a high-pressure pump sprays diesel fuel via an injector at the end of the compression stroke.

4. In petrol or gasoline engines, an AC pump and a carburetor are essential components of the fuel system.

4. In a diesel engine, a high-pressure pump and injectors are essential for the fuel system.

5. The compression ratio of a petrol or gasoline engine is 7:1 to 10:1. 

(The compression ratio may vary depending on the size and configuration of the engine.)

5. The compression ratio of a diesel engine is 12:1 to 20:1. 

(The compression ratio may vary depending on the size and configuration of the engine.)

6. Petrol or gasoline engines are light in weight.

6. Diesel engines are heavy.

7. High-quality oil is used in petrol or gasoline engines.

7. Low-quality fuel is used in diesel engines.

8. Efficiency of a petrol or gasoline engine is 25%

8. Efficiency of a diesel engine is 35%

9. The speed and load of a petrol or gasoline engine are controlled by the carburetor's throttle valve.

9. The load and speed of a diesel engine are controlled by a governor.

10. The construction of a petrol or gasoline engine is simple and straightforward.

10. The construction of a diesel engine is complex.

11. Petrol or gasoline engines have a longer lifespan, meaning they can be operated for a long time.

11. Diesel engines have a shorter lifespan; that is, they cannot be operated for as long a period as petrol or gasoline engines.

12. Petrol or gasoline engines are relatively lower in cost.

12. Diesel engines are more expensive.

Question: State the differences between a circuit breaker, auto-recloser, fuse, and isolator.

Answer: The differences between a circuit breaker, auto-recloser, fuse, and isolator are as follows:

Circuit Breaker

Auto-recloser

Fuse

Isolator

1. It can automatically disconnect the circuit during abnormal circuit conditions.

1. It can automatically disconnect the circuit in the event of a permanent fault.

1. Under abnormal circuit conditions, the fuse wire can melt and disconnect the circuit.

1. It cannot automatically disconnect the circuit under either abnormal or normal conditions.

2. Under normal conditions, it can function like a switch to connect or disconnect a circuit.

2. There is no such provision in it.

2. A fuse has no switch; while it can be connected to or disconnected from a circuit, either by hand or using a fuse puller, doing so is dangerous.

2. The operation (opening or closing) of an isolator is only possible when there is no current flowing. However, it can be opened or closed while current is flowing, provided the current level is low.

3. When a fault occurs, it disconnects the circuit, but it does not identify the fault. The relay identifies the fault.

3. It also features a mechanism similar to a circuit breaker.

3. It performs both error identification and error removal simultaneously.

3. It has no such power.

4. Operating time is longer than that of a fuse (0.1 to 0.3 seconds)

4. In this case, it takes somewhat more time, as three separate operations are required.

4. The operating time is much shorter than that of a circuit breaker (0.002 seconds or thereabouts).

4. It has no such thing as an operating time.

5. Operating a circuit breaker requires auxiliary equipment such as CTs, PTs, and relay tripping mechanisms.

5. In this case too, all those pieces of equipment are required.

5. These are not needed.

5. These are not needed.

6. Circuit breakers are used for the protection of high-voltage lines and various pieces of equipment.

6. It is particularly needed and functions quite effectively in rural systems, where transient faults on distribution lines occur more frequently.

6. Due to the lack of spark-suppression measures, it generally cannot be used on high-voltage lines.

6. It is used exclusively on low and high-voltage lines, both before and after the circuit breaker.

7. It requires regular maintenance.

7. It requires regular maintenance.

7. It does not require much maintenance.

7. It does not require much maintenance.

8. It includes a special arrangement for arc extinction.

8. It includes a special arrangement for arc extinction.

8. It does not have any special provision for arc extinguishing.

8. Attempting to open it while it is in operation results in arcing, and there are no provisions to prevent this. Furthermore, it cannot be opened or closed while it is in operation.

9. The construction of a circuit breaker is very complex and it is also expensive.

9. The construction of an auto-recloser is very complex and it is also expensive.

9. The structure is simple and the cost is low.

9. Simple construction and low cost though more expensive than a fuse.

Question: State the differences between an air circuit breaker and an oil circuit breaker.

Answer: The differences between an air circuit breaker and an oil circuit breaker are as follows:

Air Circuit Breaker

Oil circuit breaker

1. Its structure is complex.

1. Its structure is relatively simple and straightforward.

2. A supply of high-pressure air must always be kept available for operations.

2. The operation is carried out in oil.

3. Air is used for making and breaking the current-carrying contacts and for extinguishing the arc.

3. Oil is used for the purposes of insulation and arc quenching.

4. The contacts are situated in an air medium.

4. The contacts are immersed in insulating oil.

5. The likelihood of a fire occurring is very low.

5. There is a risk of fire caused by oil.

6. The arcing period is very short.

6. The arcing period is relatively longer.

7. Due to lower arc energy, the contacts sustain less damage.

7. The contacts suffer greater damage due to the higher arc energy.

8. Suitable for repeated operations.

8. Repeated operation is not very suitable, as it degrades the quality of the insulating oil.

9. Fresh air entering from the compressor acquires dielectric strength very rapidly.

9. Since fresh oil cannot be used for every operation, it is unable to attain dielectric strength so quickly.

10. It does not have a large capacity.

10. Higher-capacity units break down more quickly.